熱電偶應用中冷結點補償?shù)膶?shí)現因?yàn)闊犭娕际遣罘譁囟葴y(cè)量器件,在處理熱電偶信號時以冷結點作為參考點,考慮到非零攝氏度冷結點的電壓,必須對熱電偶輸出電壓進行冷結點補償。本文比較了幾種冷結點補償器件,并以硅溫
幾款單片機下載線應用電路ByteBlaster 下載線電路圖 ByteBlaster MV 下載線電路圖 ByteBlaster II 下載線電路圖 Ispdown下載線接口標準 Atmel單片機的編程
三種單片機模擬串口方法介紹模擬串口就是利用51的兩個輸入輸出引腳如P1.0和P1.1,置1或0分別代表高低電平,也就是串口通信中所說的位,如起始位用低電平,則將其置0,停止位為高電平,則將其置1,各種數據位和校驗位則根據情
熱電偶也叫溫差電偶,是最早出現的一種熱電探測器件。其工作原理是溫差電效應。例如,由兩種不同的導體材料構成的接點,在接點處可產生電動勢。這個電動勢的大小和方向與該接點處兩種不同的導體材料的性質和兩
分立元件組成的烙鐵電路Wattage of load10W18W25W35W65W80WValue of R5 (in ohms)330180136 (68+68)1005644 (22+22)Wattage of R5 (in watts)01020204056.5 Usually a soldering iron takes a couple of minutes
Solid State Power ControllerAbout the Circuit The ckt is built around two 555 timer ICs. U1 and U2. U1 is wired as a variable duty cycle oscillator with a constant time period of around 0.1 second. D
高低壓切斷與時間延遲關閉電路,High And Low Voltage Cut Off With Time Delay OverviewThe power line fluctuations and cut-offs cause damages to electrical appliances connected to the line. It is more
燈光控制系統電路,ht Control SystemIt is easy to install a couple of infrared emitter and receiver at the entrance of your room and maybe you connect them to the light, but you cannot control the light
紅外燈調光器電路,IR Light DimmerThis is a device for adjusting lights in your home with any type of remote controller (tv, dvd, video,). Today we are using many devices in our homes to improve quality
高電流雙極步進電機控制器電路,High current bipolar stepper motor controllerSpecifications -------------------------------------------------------------------------------- High Current Bipolar S